Unpacking & Pre-installation

Carefully remove the light bar and place it on a flat surface, taking care not to scratch the lenses or damage the cable

coming out of the bottom. Examine the unit for transit damage, broken lamps, etc. Report any damage to the carrier and

keep the shipping carton.

Standard light bars are built to operate on 12 volt D.C. negative ground (earth) vehicles. If you have an electrical system

other than 12 volt D.C. negative ground (earth), and have not ordered a specially wired light bar, contact the factory for

instructions.

Test the unit before installation. To test, touch the black wire to the ground (earth) and the other wires to +12 volts D.C.,

in accordance with the instructions attached to the cable (an automotive battery is preferable for this test). A battery

charger may be used, but please note that some electronic options (flashers, stingrays, etc.) may not operate normally

when powered by a battery charger. If problems occur at this point, contact the factory.

Installation & Mounting

MOUNTING HARDWARE - All mounting hardware is packed in a small box inside the main carton. Four standard kits

are available: (1) Hook-On Type, (1) Tow and Recovery and (2) Permanent Types. These are discussed in detail later.

Note: Hook-on mounting for "gutterless" type vehicles will require a special hook for mounting. Several special

application hooks are available. Contact the factory for details.

Utilizing non-factory supplied screws and/or mounting brackets and/or the improper

number of screws may result in loss of warranty coverage on the equipment.

WARNING!

Mounting Bracket

Bottom of Lightbar

1/4-20 Carriage Bolt

5/16" Split Lockwasher

5/16" Trim Nut

(Do Not Overtighten)

Plastic Shim (if needed)

Rubber Foot

1/4" Acorn Nut

5/16" Cap Screw

5/16" Nut

FIGURE 1

Hook-on Mounting

Begin the installation by attaching the rubber feet to the mounting brackets using the black 1/4"

carriage bolts and 1/4" nuts provided. See Figure 1. (Do not install shims at this time). Place the

light bar upside down on a table or other work surface, being careful not to scratch the lenses. Slide

the 5/16" carriage bolts into the frame. Secure the mounting brackets finger tight so they support the

weight of the light bar, but still are positionable. Locate the vehicle on a level surface. Place the light

bar on the roof of the vehicle. Place a soft pad in the center of the roof to protect the paint. The

mounting brackets must be placed so that the rubber feet are resting on the curved section of the

roof, see Figure 2. This is the strongest part of the roof. Once the light bar is centered, tighten

the mounting bracket to the light bar. Using a tape measure and a level, center

the light bar from side to side and locate a position on the roof where the

light bar is level.

Gutter Hook

5/16-18 Carriage Bolt

1 2 3 4 5 6 7 8 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Briggs & Stratton VANGUARD 540000 manuály

Uživatelské manuály a uživatelské příručky pro Příslušenství a součásti motorových vozidel Briggs & Stratton VANGUARD 540000.
Poskytujeme 1 manuály pdf Briggs & Stratton VANGUARD 540000 ke stažení zdarma podle typů dokumentů: Uživatelský manuál

Briggs stratton VANGUARD 540000 Uživatelský manuál (20 strany)

Značka: Briggs-stratton | Kategorie: Motor vehicle accessories & components | Velikost: 0.93 MB |

Tabulka s obsahem

Operating & Maintenance

Instructions

ENGINE INFORMATION

OIL CAPACITY

TYPE OF OIL TO USE

SAE Viscosity Grades

CHECKING AND ADDING OIL

MODEL 470000

STARTING & STOPPING

MAINTENANCE

ADJUSTMENTS

PARTIAL LIST OF

PART NO

element or the

À compter du 1

Další produkty a příručky pro Příslušenství a součásti motorových vozidel Briggs & Stratton

Modely	Typ Dokumentu
POWER BUILT 120000	Uživatelský manuál Briggs & Stratton POWER BUILT 120000 User's Manual, 92 stránky
Outboard Motor 540000	Uživatelský manuál Briggs & Stratton Outboard Motor 540000 User's Manual, 92 stránky
73001	Uživatelský manuál Briggs & Stratton 73001 User's Manual, 72 stránky
28T700	Specifikace Briggs & Stratton 28T700 Specifications, 12 stránky
200000	Návod k obsluze Briggs & Stratton 200000 Operator`s manual, 28 stránky
330000	Návod k obsluze Briggs & Stratton 330000 Operator`s manual, 28 stránky
44L700	Uživatelský manuál 44L700 - Ppe- pressure - washer, 16 stránky
250000	Specifikace Briggs & Stratton 250000 Specifications, 338 stránky
210000	Uživatelský manuál Briggs & Stratton 210000 Owner`s manual, 20 stránky
400000	Návod k obsluze Briggs & Stratton 400000 Operator`s manual, 20 stránky
073001	Uživatelský manuál Briggs & Stratton 073001 Owner`s manual, 25 stránky
90000 series	Návod k obsluze Briggs & Stratton 90000 series Operator`s manual, 16 stránky
522447	Specifikace Briggs & Stratton 522447 Specifications, 31 stránky
83100	Návod k obsluze Briggs & Stratton 83100 Operator`s manual, 84 stránky
THE POWER WITHIN 625 SERIES	Uživatelský manuál proven, advanced, reliable performance. [en] , 11 stránky
400000	Průvodce řešením problémů Briggs & Stratton 400000 Troubleshooting guide, 36 stránky
120000 Quantum 625 Series	Návod k obsluze Briggs & Stratton 120000 Quantum 625 Series Operator`s manual, 28 stránky
030241	Uživatelský manuál Briggs & Stratton 030241 Owner`s manual, 28 stránky
400000	Návod k obsluze Briggs & Stratton 400000 Operator`s manual, 28 stránky
522447	Specifikace Briggs & Stratton 522447 Specifications, 10 stránky