INSTALLATION& OPERATIONMANUALRead all instructions and warnings before installing and using.INSTALLER: This manual must be delivered to the end us
Master/Slave OperationEach 360 degree corner module consists of a "master" and a "slave" driver circuit board, 360 degree optics a
Directional module Flash Pattern - Table 2Flash Pattern DescriptionCycle Flash Cycles through various patterns @ 70 fpmSteady-Burn Steady-BurnFive Fla
TABLE 3 - FLASHER TYPEFeatures 360RS 360RD 360RDK 700 710/711100W (2 lights), X XAlternating Flash200W (4 lights), X XAlternating F
Multi-Functional Intersection Control System - This system allows multiple lighting options with a singlepair of intersection lights. The control cen
Operation: The Multi-Functional Intersection Control System will allow the user to obtain Takedown, Intersec-tion and Alley functions with a single pa
MaintenanceLens CleaningUse plain water and a soft cloth, or Code 3® lens polish and a very soft paper towel or facial tissue.Because plastic scratche
Maintenance for Upper and Lower Level Components(including Flasher and Stingray Electronics)Upper level components may be replaced by removing the app
Strobe Filter ReplacementRefer to Figure 17. The filter can be removed by unsnapping it from the light head and by removing the mirror ifpresent for c
The power supply can be located in three locations - Driver’s side and Passenger’s side outboards and thecenter section. The power supply location wil
MX 7000 Exploded View - Outboard Section ShownFigure 1919
IntroductionThe MX 7000® Light Bar is a dual-level light bar that is less than 6" high, yet delivers unobstructed 360° warnin
20
Parts ListRef No. Description Part No.1 #8 x .270" Sheet Metal Screw T012152 MX Torque Plate T086373 MX 1/2 Diamond Mirror S25408MMX Full Diamond
PARTS NOT SHOWNMX Top Outboard Lens Clear T02101 Red T02102 Blue T02103 Amber T02104Terminal Block - 2 Pole, 1 Row T000285/16" C
FIGURE 20Parts list No. Description Part No. Qty1 MX Strobe Motor Plate T08604 22 MX Strobe Midplate - Front T08602 23 MX Strobe Midplate - Rear T
Parts List No. Description Part No. Qty.5 Strobe Upper Lighthead Assembly -Corner Position T09424Strobe Upper Lighthead Assembly -Corner Position
1 BAYONET LAMP 50W T015402 NEW REFLECTOR ASSEMBLYRED/BLUE S22179AMBER/BLUE
D-Tech Lamp Replacement InstructionsTo remove lamp, first remove D-TechReflector Head. Press DOWN on tab androtate D-Tech head counterclockwise torem
PROBLEM POSSIBLE CAUSE SOLUTIONLighthead oscillates when selecting Lighthead not sensing position.Alley and/or Takedown modes. Check the following:Bad
STROBE OPTIONTROUBLESHOOTING GUIDEPROBLEMLight heads donot fire.. Only front strobes flashCAUSEa.Harness that connects powersupply to strobe head has
NOTES29
Unpacking & Pre-installationCarefully remove the light bar and place it on a flat surface, taking care not to scratch the lenses or damage the cab
NOTES30
NOTES31
16Code 3 & ArrowStik are registered trademarks of Code 3, Inc.MX7000, OsciLaser & Stingray are trademarks of Code 3, Inc. a subsidiary of Pub
Hook-on MountingBegin the installation by attaching the rubber feet to the mounting brackets using the black 1/4" carriage bolts and 1/4" nu
The shims provided may be used here to help level the light bar, see Figure 3. Also, the tabs on the mounting brackets may bebent at any angle to mat
WARNING!!Once the light bar is level and centered, mark the holes through the mounting tabs and remove the light bar from the vehicle.Make sure that t
Route the wiring cable into the engine or passenger compartment, taking care to use grommets and to apply sealant aroundopenings to keep water out. I
Options & SpecificationsMany options are available for the MX 7000. This section is designed to describe the function of, andmaintenance for, the
Dim OperationLightbar LED modules are equipped with a low power "Dimming" mode as standard. Dimming will be controlled byappl
Commentaires sur ces manuels